TECHNICAL FEATURES
Top-hung running track
NEW: multifunctional structural horizontal top-hung running track (patented), made in continuous mode in high-strength steel profile, shiny zinc-plated, with built-in safety and anti-slip rack.
The top-hung running track, made to measure, is prepared and pre-drilled for fastening to the support element by means of dowels (dowels not included).
Where the dimensions require a segmentation of the running track, it is suppliedwith push-fit joints.
Front cover of the running track through a RAL 7035 pre-painted sheet metal casing included for sliding doors with HN (Net Height) up to 2700 mm (over 2700 optional and on request).
Floor guide (consisting in a combination/set of bearings) positioned on the floor beyond the wall aperture, always supplied.
NEW: Stone Track ground contrast system (patented) designed for fire performance in the large dimensions.
Advanced and alternative system to be preferred to the linear guide on the ground.
Linear guide on the ground included in the supply, expected over LN 4900 mm (EI2 60 and EI2 90: length of the guide reduced to 1500 mm. EI2 120: Net wall aperture).
It is advisable to prefer the Stone Track system to this solution.
Hanging system - CARRIER
NEW: FIRE AND SMOKE BARRIER suspension and overhead sliding system (patented) consisting of a continuous steel profile element with vectorial load with integral, balanced, flex-oscillating and millimeter-accuracy carriers for uniform load distribution.
For each modular panel there are carriers equipped with double running track.
Leaf
Made with cut-to-measure modular panels assembled through coplanar male/female push-fit joints (patented) and fixed on both sides by visible screws (the screws are included in the supply).
NEW: upper reinforcing structure for the leaf connected to the carrier and lower reinforcing structure in profiled metal sheet.
Suitably shaped coating metal sheet on the two external faces with programmed deformability.
NEW: MEV FIRUX® (patented) continuous internal insulating pack, resistant to high temperatures, available even in large dimensions.
Dynamic overlapping and overall dimensions depending on the size of the sliding door, in compliance with the standard.
Guided and facilitated assembly sequence thanks to the complete preparation of all the details (thoroughly vetted at the factory) and the numerical progression shown on the panels and on the lower reinforcing structure with the absolute advantage of a successful installation and reduced installation times.
Handles
Recessed on both sides of each leaf, positioned so as to retract according to dynamic overlapping.
Smoke labyrinth seals
In press-folded and pre-drilled sheet steel for fixing by means of pre-set screws. The wall side labyrinth seals are completed with an insulating sheet and finished with FIRUX® intumescent fire seals.
FIRUX® type intumescent fire seal
Placed on all labyrinth seals and between panels.
Cold Smoke Gaskets Sa (optional)
NEW: Cold Smoke Gaskets Sa placed on the perimeter of the fixed and mobile profiles (provided on the male-female joint in the case of two leaves; applied on the perimeter of the frame in the case of a pedestrian door).
NEW: The possibility of installing the KIT Sa, as an integration, even at a later time is foreseen.
Accident prevention systems
NEW: hydraulic device (patented) for speed control VTK (Viscotroller® Kalipè®) – at a slow and short pace – which acts in synergy with the top-hung running track by coupling with the rack, therefore guaranteeing full safety when closing the door leaf with a soft and delicate closure. Life-saving device, innovative, absolute and new generation.
NEW: SAM K, soft close damper, cushions and accompanies the door during the final stage of closing.
Operation (door hold-open retainer)
Standard with electromagnet as per DoP declaration.
Counterbalance weights
Closure with counterbalance weight protected by a RAL 7035 pre-painted sheet metal casing in the various versions.
- Front
- Offset front
- Opposite side
- Opposite side offset
- NEW: fixed on the leaf, INTEGRAL WITH THE LEAF
Wicket door (optional)
Door size | Wicket door aperture dimensions | ||||
---|---|---|---|---|---|
LN (1 leaf) | LN (2 leaves) | HN | LNp | HNp | |
Wicket door with sill (92 mm) | 1580 1870 | 3500 4000 | 2250 2250 | 850 1140 | 2090 2090 |
Wicket door without sill | 1580 1870 | 3500 4000 | 2200 2200 | 850 1140 | 2000 2000 |
The measurements are expressed in mm. |
For lower LN (Net wall aperture) ask for feasibility.
In the case of a HN (Net Height) lower than the measures listed above, the height of the wicket door (HNp) is to be reduced.
Applications
- Surface mounted on solid and load-bearing masonry or reinforced concrete wall.
- On insulated and protected beam or insulated metal structure covered with plasterboard.
Finish
The sliding doors are made of galvanized sheet metal and finished with an ecological primer paint, of industrial type, with high quality epoxy resins, which guarantee protection against corrosion from a vast range of aggressive agents, acid and non-acid, in environments not directly exposed to the outdoor natural atmosphere. Standard color RAL 7035. A wide range of RAL and NCS is available on order.
NEW: execution in AISI 304 o 316 stainless steel (excluding running track, point floor guide and accessories)
Identification plate
Applied on the shell handle with the appropriate CE mark and with personalized polychrome CARD with identification data.
Documentation provided (CE marking)
Composed by:
- DoP declaration of performance
- declaration of conformity with machinery directive
- installation, use and maintenance manual
- installation instructions
EI2 60 - EI2 90 LEAF weight and thickness
- Average nominal weight 47 kg/m2
- NEW: nominal thickness 100 mm
EI2 120 LEAF weight and thickness
- Average nominal weight 51 kg/m2
- NEW: nominal thickness 120 mm
Field of application with CE marking
Sliding Door 1 Leaf EI2 60 - EI2 90 - EI2 120 | Sliding Door 2 Leaves EI2 60 - EI2 90 | Sliding Door 2 Leaves EI2 120 |
||||
---|---|---|---|---|---|---|
LN | HN | LN | HN | LN | HN | |
Maximum dimensions | 10000 mm | 8225 mm | 10000 mm | 8225 mm | 5600 mm | 5027 mm |
Maximum surface * | 50 mq | 50 mq | 50 mq | |||
Decreasing dimensions | UNLIMITED | UNLIMITED | UNLIMITED |
* Maximum area provided for by the standard for a CE marked product.
TECHNICAL DATA SHEET
Do you need help? Contact us
Write or call us for more information on the new fire doors with CE marking.